MYLEX CORPORATION
DCE376
| 
 
  | 
Data bus: 32 bit, EISA
Size: Full-length, full-height card
Hard drives supported: Up to seven SCSI devices
Floppy drives supported: Two 360KB, 720KB, 1.2MB, or 1.44MB
Maximum heads/cyl.: 16 heads and 2048 cylinders
| 
 CONNECTIONS  | |
| 
 Function  | 
 Location  | 
| 
 34-pin data cable connector-floppy drive  | 
 P0  | 
| 
 50-pin SCSI connector-internal  | 
 P3  | 
| 
 4-pin connector-drive active LED  | 
 P5  | 
| 
 USER CONFIGURABLE SETTINGS (FOR REV 1D)  | |||
| 
 Function  | 
 Location  | 
 Setting  | |
| » | 
 Factory configured - do not alter  | 
 J1 & J2  | 
 pins 2 & 3 closed  | 
| » | 
 Supports 64K PROM  | 
 J5  | 
 pins 2 & 3 closed  | 
| 
 Supports 128K PROM  | 
 J5  | 
 pins 1 & 2 closed  | |
| » | 
 Hard Drive Interrupt IRQ14 enabled  | 
 J10  | 
 pins 1 & 2 closed  | 
| 
 Hard Drive Interrupt IRQ14 disabled  | 
 J10  | 
 open  | |
| » | 
 Factory configured - do not alter  | 
 J11  | 
 pins 2 & 3 closed  | 
| » | 
 Factory configured - do not alter  | 
 J12 & J13  | 
 pins 1 & 2 closed  | 
| 
 USER CONFIGURABLE SETTINGS (FOR REV 1E)  | |||
| 
 Function  | 
 Location  | 
 Setting  | |
| » | 
 Supports 64K PROM  | 
 J1  | 
 pins 2 & 3 closed  | 
| 
 Supports 128K PROM  | 
 J1  | 
 pins 1 & 2 closed  | |
| » | 
 Factory configured - do not alter  | 
 J2  | 
 pins 2 & 3 closed  | 
| » | 
 Factory configured - do not alter  | 
 J9  | 
 pins 2 & 3 closed  | 
| » | 
 Hard Drive Interrupt IRQ14 enabled  | 
 J10  | 
 pins 1 & 2 closed  | 
| 
 Hard Drive Interrupt IRQ14 disabled  | 
 J10  | 
 open  | |
| » | 
 Floppy drive enabled  | 
 J11  | 
 pins 2 & 3 closed  | 
| 
 Floppy drive disabled (Revisions prior to "1E" require special PROM's)  | 
 
 J11  | 
 
 pins 1 & 2 closed  | |
| » | 
 Factory configured - do not alter  | 
 J12  | 
 pins 1 & 2 closed  | 
| » | 
 DCE376 emulates primary controller position  | 
 J13  | 
 pins 1 & 2 closed  | 
| 
 DCE376 emulates secondary controller position  | 
 J13  | 
 pins 2 & 3 closed  | |
| 
 Factory setting for 3Px firmware  | 
 J14  | 
 pins 1 & 2 closed  | |
| 
 Factory setting for 2Px firmware  | 
 J14  | 
 pins 2 & 3 closed  | |
| » | 
 Factory configured - do not alter  | 
 J16  | 
 open  | 
| 
 CACHE CONFIGURATION (FOR REV 1D)  | ||||||
| 
 Size  | 
 J3  | 
 J4  | 
 J6  | 
 J7  | 
 J8  | 
 J9  | 
| 
 256KB  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
 open  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
| 
 1024KB  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
 open  | 
 pins 1 & 2  | 
 pins 2 & 3  | 
 pins 1 & 2  | 
| 
 4096KB  | 
 pins 2 & 3  | 
 open  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
| 
 Note:Pins designated should be in the closed position.  | ||||||
| 
 CACHE CONFIGURATION (FOR REV 1E)  | ||||||
| 
 Size  | 
 J3  | 
 J4  | 
 J5  | 
 J6  | 
 J7  | 
 J8  | 
| 
 256KB  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
 open  | 
 pins 1 & 2  | 
 pins 1 & 2  | 
| 
 1024KB  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
 pins 1 & 2  | 
 open  | 
 pins 2 & 3  | 
 pins 1 & 2  | 
| 
 4096KB  | 
 pins 2 & 3  | 
 open  | 
 2-3 closed  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
 pins 2 & 3  | 
| 
 Note:Pins designated should be in the closed position.  | ||||||