Card Type	Modem
Chip Set	Unidentified
Maximum Modem Rate	56.0Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	ITU-T V.21, V.22, V.22bis,V.23, V.32, V.32bis, V.34, K56flex
Fax Modulation Protocol	V.17, V.29, V.27
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	PCMCIA

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &P, &T, &V, &W, &Y, &Z

Extended AT commands

\A, \B, \K, \N

%C, %E, %L, %Q

#CID

S Registers

S0, S1, S2, S3, S4, S5, S6 ,S7, S8, S9, S10, S12, S18, S29, S30, S32, S33

Special commands

+MS, -K

Note: See MHI Help File for full command documentation.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
í N1	Auto-mode detection enabled

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects communications mode options
Command	Mode
&Q0	Asynchronous mode, serial port speed follows connect speed.
í &Q5	Error correction mode
&Q6	Buffered asynchronous mode

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
í &S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Command	Function
&D0	DTR override
&D1	DTR toggle causes online command mode
í &D2	Normal DTR operations
&D3	Resets on receipt of DTR

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DS=n	Dial stored telephone number n
DT	Tone dialing enabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by 5 seconds of silence
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.
D^	Toggle calling tone

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Factory default profile 0
&F1	Factory default profile 1

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	RTS/CTS & XON/XOFF flow control enabled

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Note: Used primarily for international data transmission
Command	Function
í &G0	Guard tone disabled
&G2	1800Hz guard tone enabled

LINE MODULATION
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	For compatibility only; non-functional. Use +MS to select line modulation

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports maximum line speed
I1	Reports product type
I2	Reports checksum firmware
I3	Reports product name
I4	Reports firmware release
I5	Reports active Country Code

RTS/CTS
Type:	Configuration
Format:	AT [cmds] &Rn [cmds]
Description:	Selects RTS/CTS options
Command	Function
&R0	In asynchronous mode, C106 is controlled according to V.25 handshake recommendation
í &R1	In synchronous mode, C106 follows flow control

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

TRANSMISSION LEVEL - FAX
Type:	Register
Format:	AT [cmds] S92=n [cmds]
Range:	3-15
Unit:	-1 dBm
Description:	Sets the signal level for transmission while in fax mode

TRANSMISSION LEVEL - LEASED-LINE
Type	Register or Configuration
Format	AT [cmds] S91=n [cmds]
Range	3-15
Unit	-1 dBm
Description	Sets the signal level for transmission over leased-lines