Card Type	Modem (asynchronous), Ethernet
Chipset	Unidentified
Network Transfer Rate	10Mbps
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation	Bell 103A/212A ITU-T V.22, V.22bis, V.23, V.23bis, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10EC, V.42, V.42bis
Topology	Linear Bus/Star
Wire Type	Unshielded twisted pair RG-58A/U 50ohm coaxial
Boot ROM	Not available

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &Q, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \J, \K, \L, \N

%C, %E, %TT

Special AT Commands

:E, *H, -K, )M, @M, +MS, -Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S28, S29, S30, S32, S33, S36, S38, S39, S40, S46, S48, S82, S86, S91, S92, S95, S201

Note: See MHI documentation for complete information.

UNIDENTIFIED COMMANDS
Command	Default
S27	73
S31	198
S37	0
S41	195

CELLULAR STATUS INDICATOR
Format:			AT [cmds] ^T6 [cmds]
Default:			Read only
Range:			0-255
Description:			Indicates the status of cellular phone.
Bit	Value			Function
0	0 1			Cellular phone is not receiving a call. Cellular phone is receiving a call.
1		0 1			Cellular phone is not in use. Cellular phone is in use.
2		0 1			Cellular phone is not locked. Cellular phone is locked.
3		0 1			Cellular service detected. Cellular service not detected.
4		0 1			Cellular phone is powered off. Cellular phone is powered on.
5		0 1			Cellular driver is initialized. Cellular driver is not initialized.
6		0			Not used.
7		0 1			Land line detected. Cellular cable detected.

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials the telephone number indicated according to any modifiers included in the string.
Command	Function
DJ	MNP10 link will be negotiated at 1200bps for this call.
DK	MNP10 power level adjustment enabled for this call.
DL	Re-dial last number.
DP	Pulse dialing enabled.
DS=n	Dial stored telephone number n.
DT	Tone dialing enabled.
DW	Dialing resumed following dial tone detection.
D,	Dialing paused for amount of time specified in S8 register.
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D^	Calling tone disabled for this call.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DISPLAY CELLULAR DRIVER
Type:	Immediate
Format:	AT [cmds] ^I [cmds]
Description:	Displays cellular phone driver information.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] I4 [cmds]
Description:	Reports the product identification string.