THINFAX 1414I, THINFAX 1414C

EXP COMPUTER, INC.

Card Type

Modem (synchronous/asynchronous)

Chipset

Unidentified

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10, V.42, V.42bis

Fax Class

Class I & II

Data Bus

PCMCIA Type II

53277

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \G, \K, \L, \N

%C, %E, %L, %Q, %TT

Special AT Commands

:E, *H, -K, )M, @M, -Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92

S95, S99, S201

Note: See MHI help file for complete information.

UNIDENTIFIED COMMANDS

Command

Default

S37

0

S80

0

Proprietary AT Command Set

AUTOSYNC OPTIONS

Type:

Register

Format

AT [cmds] S19=n [cmds]

Default:

26

Range:

0 - 30

Description:

Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle.

Bit

Value

Function

0

0

Not used

1

0

í 1

Binary synchronous protocol used.

HDLC protocol used.

2

í 0

1

HDLC address detect disabled.

HDLC address detect enabled.

3

0

í 1

NRZI bit coding used.

NRZ bit coding used.

4

0

í 1

HDLC idle sends MARK.

HDLC idle sends FLAG or SYNC.

AUTOSYNC HDLC ADDRESS

Type:

Register

Format:

AT [cmds] S20=n [cmds]

Default:

0

Range:

0-255

Unit:

Unidentified

Description:

Sets the HDLC address and binary synchronous character.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Displays product identification code.

I1

Displays ROM checksum.

I2

Tests and displays ROM checksum result.

I3

Displays firmware model, revision, and interface type.

I4

Displays OEM response.

I5

Displays country code.

I6

Displays data pump model.

PROTOCOL/SPEED

Type:

Configuration

Format:

AT [cmds] Fn [cmds]

Description:

Selects the protocol and speed the modem will attempt to connect at.

Command

Function

F0

Auto-detect the highest common connect speed.

F1

Select V.21 or Bell 103 at 300bps speed.

F3

Select V.23 at 75/1200bps speed.

F4

Select V.22 or Bell 212A at 1200bps speed.

F5

Select V.22bis at 2400bps speed.

F6

Select V.32 or V.32bis at 4800bps speed.

F7

Select V.32bis at 7200bps speed.

F8

Select V.32bis or V.32 at 9600bps speed.

F9

Select V.32bis at 12Kbps speed.

F10

Select V.32bis at 14.4Kbps speed.

REMOTE CONFIGURATION CHARACTER

Type:

Register

Format:

AT [cmds] S202=n [cmds]

Default:

170

Range:

0 - 255

Unit:

1 ASCII character

Description:

Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character.

Card Type	Modem (synchronous/asynchronous)
Chipset	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis
Fax Class	Class I & II
Data Bus	PCMCIA Type II

AUTOSYNC OPTIONS
Type:		Register
Format		AT [cmds] S19=n [cmds]
Default:		26
Range:		0 - 30
Description:		Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle.
Bit	Value	Function
0	0	Not used
1	0 í 1	Binary synchronous protocol used. HDLC protocol used.
2	í 0 1	HDLC address detect disabled. HDLC address detect enabled.
3	0 í 1	NRZI bit coding used. NRZ bit coding used.
4	0 í 1	HDLC idle sends MARK. HDLC idle sends FLAG or SYNC.

AUTOSYNC HDLC ADDRESS
Type:	Register
Format:	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	Sets the HDLC address and binary synchronous character.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Tests and displays ROM checksum result.
I3	Displays firmware model, revision, and interface type.
I4	Displays OEM response.
I5	Displays country code.
I6	Displays data pump model.

PROTOCOL/SPEED
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the protocol and speed the modem will attempt to connect at.
Command	Function
F0	Auto-detect the highest common connect speed.
F1	Select V.21 or Bell 103 at 300bps speed.
F3	Select V.23 at 75/1200bps speed.
F4	Select V.22 or Bell 212A at 1200bps speed.
F5	Select V.22bis at 2400bps speed.
F6	Select V.32 or V.32bis at 4800bps speed.
F7	Select V.32bis at 7200bps speed.
F8	Select V.32bis or V.32 at 9600bps speed.
F9	Select V.32bis at 12Kbps speed.
F10	Select V.32bis at 14.4Kbps speed.

REMOTE CONFIGURATION CHARACTER
Type:	Register
Format:	AT [cmds] S202=n [cmds]
Default:	170
Range:	0 - 255
Unit:	1 ASCII character
Description:	Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character.