Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I
Data Modulation Protocol	Bell 103J/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, D, E, H, I, L, M, O, P, Q, S, T, V, W, X, Y, Z

&C, &D, &F, &G, &P, &S, &T, &W, &Y, &Z

Extended AT Commands

%A, %C, %F, %G, \A, \B, \C, \E, \G, \J, \K, \N, \Q, \T, \V, \X

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25, S26

Special Commands

-K, -Q, )M, *H, :E, @M

Note: See MHI Help file for full command documentation.

BIT MAPPED S-REGISTERS
Register	Default
S14	170
S21	48
S22	118
S23	31
S27	64

BIT MAPPED :T-REGISTERS
Register	Default
:T15	128
:T19	1
:T23	Unidentified
:T26	0

PROPRIETARY AT% COMMANDS
Command	Description	Default
%B	Modem port data rate	%B28800
%D	Disconnect buffer delay	%D0
%I	Edit connection security password	Unidentified
%L	Speed matching	%L1
%O	V.23 equalizer control	%O1
%R	Display all registers	None
%U	Clear serial port speed	%U2
%V	Display modem firmware version	None
%W	Pulse digit command	%W0

PROPRIETARY AT\ COMMANDS
Command	Description	Default
\D	Serial port DSR/CTS control	\D0
\F	Display stored phone numbers	None
\H	Hewlett Packard ENQ/ACK	\H0
\P	Write a stored phone number	None
\R	Serial port ring indicator	\R1
\S	Display on-line status	None

PROPRIETARY AT- COMMANDS
Command	Description	Default
-D	Repeat dial	None
-M	MNP class connect message	-M0
-O	Serial port parity	-O4
-P	Check parity	-P0

PROPRIETARY AT$ COMMANDS
Command	Description	Default
$A	Auto-answer auto-logon	$A0
$B	Serial port data rate	$B38400
$D	Power-up diagnostics	None
$G	Dial access security	$G0
$H	Edit Dial access security database	None
$I	Display Dial access security database	None
$J	Clear dial database	None
$L	Logon sequence	None
$M	Verify connection security password	$M0
$N	List connection security passwords	None
$P	Database security password	None
$V	Logon view mode	$V1

PROPRIETARY AT) COMMANDS
Command	Description	Default
)H	Auto-dial connection restore timer	)H0
)Q	Serial port inactivity timer	)Q5

PROPRIETARY AT* COMMANDS
Command	Description	Default
*A	Request remote access	None
*E	Enable remote access	*E0
*M	Modify remote access level	None
*P	Remote access passwords	None
*Q	Recover remote access configuration	None
*R	Enable remote access security	*R0
*S	Remote access attention character	*S42
*U	Update remote access configuration	None
*W	Store complete configuration	*W0
*X	Exit remote access	None

PROPRIETARY AT: COMMANDS
Command	Description	Default
:D	Manual dial	:D0
:K	Kermit/UUCP protocol	:K0
:Q	Kermit mark character	:Q1
:U	DCD time delay	:U0
:V	CTS time delay	:V0
:X	DSR time delay	:X0

PROPRIETARY AT@ COMMANDS
Command	Description	Default
@C	CTS/DSR/CD connect message	@C0

PROPRIETARY AT^ COMMANDS
Command	Description	Default
^V	Display bootstrap revision	None

PROPRIETARY AT:T REGISTERS
Command	Description	Default
:T0	V.22/22bis/32 mode timer	40
:T1	V.23 split-speed mode timer	30
:T2	V.21 mode timer	0
:T3	V.21/23 answer tone timer	3
:T4	Line turnaround delay-carrier on timer	20
:T5	V.23 intercharacter delay timer	7
:T6	DCD turn on delay timer	200
:T7	False answer abort timer	60
:T14	Connect message delay timer	0
:T16	CTS turn on delay timer	0
:T17	V.32/32bis connection training timer	0
:T22	DSR timer	34
:T29	Parallel packet size	16