ROCKWELL K56FLEX

WESTECH KOREA, INC.

ROCKWELL K56FLEX

Card Type

Modem

Chip Set

Rockwell

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32ter, V.32bis, V.34, V.90

Fax Modulation Protocol

ITU-T V.17, V.21 CH2, V.27ter, V.29, V.33

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

I & II

Data Bus

PCMCIA

55306

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \K, \N, \V

%C, %E, %L, %Q

Special Commands

+MS, -K, #CID

S Registers

S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S22, S23, S24, S25, S26, S27

S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95

Note:

See MHI Help File for full command documentation. Specific S-register information unavailable; S-registers may vary slightly from MHI help file.

PROPRIETARY AT COMMAND SET

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake follows interface speed

N1

Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake at highest possible speed with fallback to lower speed if necessary

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Fn [cmds]

Description:

Selects the communication protocol for data calls

Command

Protocol

F0

Auto-mode detection enabled

F1

V.21 or Bell 103

F2

Reserved

F3

V.23

F4

V.22 or Bell 212/A at 1200bps

F5

V.22bis

F6

V.32 or V.32bis at 4800bps

F7

V.32bis at 7200bps

F8

V.32 or V.32bis at 9600bps

F9

V.32bis at 12.0Kbps

F10

V.32bis at 14.4Kbps

CONFIGURATION PROFILES

Type:

Immediate

Format:

AT [cmds] &V [cmds]

Description:

Displays active and stored configuration profiles

Command

Function

&V0

Display current configurations

&V1

Display connection statistics

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

&Q Setting

&D0

&D1

&D2

&D3

&Q0, &Q5, &Q6

Command 0

Command 1

Command 2

Command 4

&Q1, &Q4

Command 2

Command 1

Command 2

Command 4

&Q2, &3

Command 2

Command 2

Command 2

Command 2

Command

Function

Command 0

Modem does not respond to DTR

Command 1

Modem goes to command mode after DTR goes is off

Command 2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

Command 3

Modem is initialized after DTR goes off

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

&F0

Load factory configuration 0

&F1

Load factory configuration 1

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

&K6

Unidirectional XON/XOFF flow control enabled

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Command

Function

&G0

Guard tone disabled

&G1

Guard tone disabled

&G2

1800Hz guard tone enabled

JACK TYPE

Type:

Configuration

Format:

AT [cmds] &Jn [cmds]

Description:

For purposes compatibility only. Performs no function

LINE TYPE

Type:

Configuration

Format:

AT [cmds] &Ln [cmds]

Description:

Selects line type

Command

Line Type

&L0

Switched line (PSTN/Dial-up)

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports firmware version and application codes

I4

Reports OEM identifier string in either binary or ASCII format

I5

Reports country code

I6

Reports data pump model and internal code

I7

Reports DAA code

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting

TRANSMIT CARRIER

Type:

Configuration

Format:

AT [cmds] Cn [cmds]

Description:

Command non-functional; for compatibility only. Returns OK

SPECIAL COMMANDS

BLACKLIST

Type:

Immidiate

Format:

AT [cmds] *B [cmds]

Description:

Displays blacklisted numbers. If no numbers are blacklisted, returns OK.

COUNTRY SELECT

Type:

Configuration

Format:

AT [cmds] *NCn [cmds]

Range:

1 - 8

Description:

Selects country code from NVRAM

DELAY

Type:

Immidiate

Format:

AT [cmds] *D [cmds]

Description:

Displays delayed numbers with the delay associated with each. If no numbers are delayed, returns OK.

DISTINCTIVE RING

Type:

Immediate

Format:

AT [cmds] -SDR=n [cmds]

Description:

Selects the distinctive ring settings

Command

Function

-SDR=0

Distinctive ring disabled

-SDR=1

Type 1 enabled

-SDR=2

Type 2 enabled

-SDR=3

Type 1 and 2 enabled

-SDR=4

Type 3 enabled

-SDR=5

Type 1 and 3 enabled

-SDR=6

Type 2 and 3 enabled

-SDR=7

Type 1, 2, and 3 enabled

FLASH MEMORY

Type:

Configuration

Format:

AT [cmds] **n [cmds]

Description:

Controls download to flash memory

Command

Function

**0

Downloads into flash memory at last sensed speed

**1

Downloads into flash memory at 38.4Kbps

**2

Downloads into flash memory at 57.6Kbps

MNP10 - POWER LEVEL ADJUST

Type:

Configuration

Format:

AT [cmds] -SEC=n [cmds]

Range:

0-30

Unit:

-1dBm

Description:

Controls automatic transmit power level adjustment during MNP 10 link negotiation

Command

Function

-SEC=0

MNP10 disabled. Transmission level is set in the S91 register

-SEC=1, [tx_lev]

MNP10 enabled. Set transmit level

PLUG & PLAY SERIAL NUMBER

Type:

Immediate

Format:

AT [cmds] %7n [cmds]

Range:

8

Unit:

Hexidecimal

Description:

Sets and stores numbers for serial plug & play

PLUG & PLAY VENDOR ID & PRODUCT NUMBER

Type:

Immediate

Format:

AT [cmds] %8n [cmds]

Range:

3 (ASCII), 4 (hex)

Unit:

ASCII, Hexidecimal

Description:

Sets and stores numbers for serial plug & play

RPI/VIDEO READY MODE

Type:

Configuration

Format:

AT [cmds] +Hn [cmds]

Description:

Enables/disables RPI & video ready mode

Command

Function

+H0

RPI/video ready mode disabled

+H1

RPI at 19.2Kbps DTE speed enabled

+H2

RPI at 38.4Kbps DTE speed enabled

+H3

RPI at 57.6Kbps DTE speed enabled

+H11

RPI + mode enabled

+H16

Video ready mode enabled

S(STATUS) -REGISTERS

AUTOSYNC OPTIONS

Type:

Register

Format

AT [cmds] S19=n [cmds]

Description:

Sets autosync options. Further information is unavailable

AUTOSYNC/SYNC

Type:

Register

Format

AT [cmds] S20=n [cmds]

Range:

0-255

Unit:

Unidentiified

Description:

Sets autosync HDLC address or BSC sync character. Further information is unavailable

BIT-MAPPED REGISTER S21

Type:

Register

Format

AT [cmds] S21=n [cmds]

Range:

Unidentiified

Description:

Selects V.24/General bit mapped options. Further information is unavailable

Card Type	Modem
Chip Set	Rockwell
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32ter, V.32bis, V.34, V.90
Fax Modulation Protocol	ITU-T V.17, V.21 CH2, V.27ter, V.29, V.33
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	I & II
Data Bus	PCMCIA

SUPPORTED COMMAND SET
Basic AT Commands
AT, A/
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z
&C, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z
Extended AT Commands
\A, \B, \K, \N, \V
%C, %E, %L, %Q
Special Commands
+MS, -K, #CID
S Registers
S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S22, S23, S24, S25, S26, S27
S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95
Note:	See MHI Help File for full command documentation. Specific S-register information unavailable; S-registers may vary slightly from MHI help file.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake follows interface speed
N1	Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake at highest possible speed with fallback to lower speed if necessary

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the communication protocol for data calls
Command	Protocol
F0	Auto-mode detection enabled
F1	V.21 or Bell 103
F2	Reserved
F3	V.23
F4	V.22 or Bell 212/A at 1200bps
F5	V.22bis
F6	V.32 or V.32bis at 4800bps
F7	V.32bis at 7200bps
F8	V.32 or V.32bis at 9600bps
F9	V.32bis at 12.0Kbps
F10	V.32bis at 14.4Kbps

CONFIGURATION PROFILES
Type:	Immediate
Format:	AT [cmds] &V [cmds]
Description:	Displays active and stored configuration profiles
Command	Function
&V0	Display current configurations
&V1	Display connection statistics

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
&Q Setting		&D0	&D1	&D2	&D3
&Q0, &Q5, &Q6		Command 0	Command 1	Command 2	Command 4
&Q1, &Q4		Command 2	Command 1	Command 2	Command 4
&Q2, &3		Command 2	Command 2	Command 2	Command 2
Command	Function
Command 0	Modem does not respond to DTR
Command 1	Modem goes to command mode after DTR goes is off
Command 2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
Command 3	Modem is initialized after DTR goes off

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Load factory configuration 0
&F1	Load factory configuration 1

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
&K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled
&K5	Transparent XON/XOFF flow control enabled
&K6	Unidirectional XON/XOFF flow control enabled

GUARD TONE
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Commands the modem to transmit a guard tone in V.22/V.22bis
Command	Function
&G0	Guard tone disabled
&G1	Guard tone disabled
&G2	1800Hz guard tone enabled

JACK TYPE
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Description:	For purposes compatibility only. Performs no function

LINE TYPE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Selects line type
Command	Line Type
&L0	Switched line (PSTN/Dial-up)

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports firmware version and application codes
I4	Reports OEM identifier string in either binary or ASCII format
I5	Reports country code
I6	Reports data pump model and internal code
I7	Reports DAA code

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
L2	Medium volume setting
L3	Highest volume setting

TRANSMIT CARRIER
Type:	Configuration
Format:	AT [cmds] Cn [cmds]
Description:	Command non-functional; for compatibility only. Returns OK

BLACKLIST
Type:	Immidiate
Format:	AT [cmds] *B [cmds]
Description:	Displays blacklisted numbers. If no numbers are blacklisted, returns OK.

COUNTRY SELECT
Type:	Configuration
Format:	AT [cmds] *NCn [cmds]
Range:	1 - 8
Description:	Selects country code from NVRAM

DELAY
Type:	Immidiate
Format:	AT [cmds] *D [cmds]
Description:	Displays delayed numbers with the delay associated with each. If no numbers are delayed, returns OK.

DISTINCTIVE RING
Type:	Immediate
Format:	AT [cmds] -SDR=n [cmds]
Description:	Selects the distinctive ring settings
Command	Function
-SDR=0	Distinctive ring disabled
-SDR=1	Type 1 enabled
-SDR=2	Type 2 enabled
-SDR=3	Type 1 and 2 enabled
-SDR=4	Type 3 enabled
-SDR=5	Type 1 and 3 enabled
-SDR=6	Type 2 and 3 enabled
-SDR=7	Type 1, 2, and 3 enabled

FLASH MEMORY
Type:	Configuration
Format:	AT [cmds] **n [cmds]
Description:	Controls download to flash memory
Command	Function
**0	Downloads into flash memory at last sensed speed
**1	Downloads into flash memory at 38.4Kbps
**2	Downloads into flash memory at 57.6Kbps

MNP10 - POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] -SEC=n [cmds]
Range:	0-30
Unit:	-1dBm
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
-SEC=0	MNP10 disabled. Transmission level is set in the S91 register
-SEC=1, [tx_lev]	MNP10 enabled. Set transmit level

PLUG & PLAY SERIAL NUMBER
Type:	Immediate
Format:	AT [cmds] %7n [cmds]
Range:	8
Unit:	Hexidecimal
Description:	Sets and stores numbers for serial plug & play

PLUG & PLAY VENDOR ID & PRODUCT NUMBER
Type:	Immediate
Format:	AT [cmds] %8n [cmds]
Range:	3 (ASCII), 4 (hex)
Unit:	ASCII, Hexidecimal
Description:	Sets and stores numbers for serial plug & play

RPI/VIDEO READY MODE
Type:	Configuration
Format:	AT [cmds] +Hn [cmds]
Description:	Enables/disables RPI & video ready mode
Command	Function
+H0	RPI/video ready mode disabled
+H1	RPI at 19.2Kbps DTE speed enabled
+H2	RPI at 38.4Kbps DTE speed enabled
+H3	RPI at 57.6Kbps DTE speed enabled
+H11	RPI + mode enabled
+H16	Video ready mode enabled

AUTOSYNC OPTIONS
Type:	Register
Format	AT [cmds] S19=n [cmds]
Description:	Sets autosync options. Further information is unavailable

AUTOSYNC/SYNC
Type:	Register
Format	AT [cmds] S20=n [cmds]
Range:	0-255
Unit:	Unidentiified
Description:	Sets autosync HDLC address or BSC sync character. Further information is unavailable

BIT-MAPPED REGISTER S21
Type:	Register
Format	AT [cmds] S21=n [cmds]
Range:	Unidentiified
Description:	Selects V.24/General bit mapped options. Further information is unavailable