;
; M7RA-1.ASM  This overlay has been adapted for the Royal Alphatronic.  
; The Royal uses a 8251-A USART which can be software defined except for 
; baud rate which must be hardware selected inside the machine.
;
; Port 41H can be programmed with the proper mode and control commands.  
; The chip select command is MVI  A,0CH, the internal reset command is 
; MVI A,40H, the mode command is MVI A,4EH for 8 data bits, no parity, 1 
; stop bit.  The command instruction is MVI A,37H (all out MODCTL2)
;
; M7DP-1.ASM -- Datapoint 1560 overlay file for MDMxx2.  11/11/83
;
; You will want to look this file over carefully. There are a number of
; options that you can use to configure the program to suit your taste.
; This file adapts the Datapoint 1560 computer to the modem program.
; Much of the information contained here is not in the main file.

; Edit this file for your preferences then follow the "TO USE:" example
; shown below.
;
;	TO USE: First edit this file filling in answers for your own
;		equipment.  Then assemble with ASM.COM or equivalent
;		assembler.
;
;       Load M7xx-1 into MEX.COM using MLOADxx
;
;       A>MLOADxx NEWMEX.COM=MEX.COM,xxxxxx.HEX
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   
; 07/11/88 - Renamed to M7RA-1.ASM              - Lee Bradley
; 11/11/87 - Renamed to M7RA-4D.ASM, added INITMOD: - Charles Battista		       
; 11/11/83 - Renamed to M7DP-1.ASM, no changes	- Irv Hoff
; 07/27/83 - Renamed to work with MDM712	- Irv Hoff
; 07/01/83 - Revised to work with MDM711	- Irv Hoff
; 06/22/83 - Revised to work with MDM710	- Irv Hoff
; 05/25/83 - Updated to work with MDM709	- Irv Hoff
; 05/15/83 - Revised to work with MDM708	- Irv Hoff
; 04/11/83 - Updated to work with MDM707	- Irv Hoff
; 04/04/83 - Updated to work with MDM706	- Irv Hoff
; 02/27/83 - Updated to work with MDM705	- Irv Hoff
; 02/17/83 - Modified MDM703CF for Datapoint
;	     1560 computers using an exter-
;	     nal modem				- Irv Hoff
;
; =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =   =
;
BELL:		EQU	07H		;bell
CR:		EQU	0DH		;carriage return
ESC:		EQU	1BH		;escape
LF:		EQU	0AH		;linefeed
;
YES:		EQU	0FFH
NO:		EQU	0
;
;
PORT:		EQU	040H		;Royal Alphatronic Data Port
MODCTL1:	EQU	PORT+1		;Modem status port
MODCTL2:	EQU	PORT+1		;Modem control port
MODDATP:	EQU	PORT		;Modem data port
;
;
		ORG	100H
;
		DS	3	;(for  "JMP   START" instruction)
;

PMMIMODEM:	DB	NO	;yes=PMMI S-100 Modem			103H
SMARTMODEM:	DB	NO	;yes=HAYES Smartmodem			104H
TONEPULSE:	DB	'P'	;T=tone, P=Pulse (Smartmodem-only)	105H
CLOCK:		DB	40	;clock speed in MHz x10, 25.5 MHz max.	106H
				;20=2 MHh, 37=3.68 MHz, 40=4 MHz, etc.
MSPEED: 	DB	5	;0=110 1=300 2=450 3=600 4=710 5=1200	107H
				;6=2400 7=4800 8=9600 9=19200 default
BYTDLY: 	DB	5	;0=0 delay  1=10ms  5=50 ms - 9=90 ms	108H
				;default time to send character in ter-
				;minal mode file transfer for slow BBS.
CRDLY:		DB	5	;0=0 delay 1=100 ms 5=500 ms - 9=900 ms 109H
				;default time for extra wait after CRLF
				;in terminal mode file transfer
NOOFCOL:	DB	5	;number of DIR columns shown		10AH
SETUPTST:	DB	NO	;yes=user-added Setup routine		10BH
SCRNTEST:	DB	YES	;Cursor control routine 		10CH
ACKNAK: 	DB	YES	;yes=resend a record after a non-ACK	10DH
				;no=resend a record only after NAK
BAKKUPBYTE:	DB	NO	;yes=change any file same name to .BAK	10EH
CRCDFLT:	DB	YES	;yes=default to CRC checking		10FH
TOGGLECRC:	DB	YES	;yes=allow toggling of CRC to Checksum	110H
CONVBKSP:	DB	NO	;yes=convert backspace to rub		111H
TOGGLEBK:	DB	NO	;yes=allow toggling of bksp to rub	112H
ADDLF:		DB	NO	;no=no LF after CR to send file in	113H
				;terminal mode (added by remote echo)
TOGGLELF:	DB	YES	;yes=allow toggling of LF after CR	114H
TRANLOGON:	DB	YES	;yes=allow transmission of logon	115H
				;write logon	      at location LOGON
SAVCCP: 	DB	YES	;yes=do not overwrite CCP		116H
LOCONEXTCHR:	DB	NO	;yes=local command if EXTCHR precedes	117H
				;no=external command if EXTCHR precedes
TOGGLELOC:	DB	YES	;yes=allow toggling of LOCONEXTCHR	118H
LSTTST: 	DB	YES	;yes=printer available on printer port	19H
XOFFTST:	DB	NO	;yes=chcks for XOFF from remote while	11AH
				;sending a file in terminal mode
XONWAIT:	DB	NO	;yes=wait for XON after CR while	11BH
				;sending a file in terminal mode
TOGXOFF:	DB	YES	;yes=allow toggling of XOFF checking	11CH
IGNORCTL:	DB	YES	;yes=CTL-chars above ^M not displayed	11DH
EXTRA1: 	DB	0	;for future expansion			11EH
EXTRA2: 	DB	0	;for future expansion			11FH
BRKCHR		DB	'@'-40H ;Send a 300 ms. break tone		120H
NOCONNCT:	DB	'N'-40H ;^N = Disconnect from phone line	121H
LOGCHR: 	DB	'L'-40H ;^L = Send logon			122H
LSTCHR: 	DB	'P'-40H ;^P = Toggle printer			123H
UNSAVE: 	DB	'R'-40H ;^R = Close input text buffer		124H
TRANCHR:	DB	'T'-40H ;^T = Transmit file to remote		125H
SAVECHR:	DB	'Y'-40H ;^Y = Open input text buffer		126H
EXTCHR: 	DB	'^'-40H ;^^ = Send next character		127H
;
;
		DS	2		;				128H
;
IN$MODCTL1:	IN	MODCTL1 ! RET	;in modem control port		12AH
		DS	7
OUT$MODDATP:	OUT	MODDATP ! RET	;out modem data port		134H
		DS	7
IN$MODDATP:	IN	MODDATP ! RET	;in modem data port		13EH
		DS	31
;
LOGONPTR:	DW	LOGON		;for user message.		160H
		DS	6		;				162H
JMP$GOODBYE:	JMP	GOODBYE 	;				168H
JMP$INITMOD:	JMP	INITMOD 	;go to user written routine	16BH
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	16EH
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	171H
		RET  !	NOP  !	NOP	;(by-passes PMMI routine)	174H
JMP$SETUPR:	JMP	SETUPR		;				177H
JMP$SPCLMENU:	JMP	SPCLMENU	;				17AH
JMP$SYSVER:	JMP	SYSVER		;				17DH
JMP$BREAK:	JMP	SENDBRK 	;				180H
;
;
; Do not change the following six lines.
;
JMP$ILPRT:	DS	3		;				183H
JMP$INBUF	DS	3		;				186H
JMP$INLNCOMP:	DS	3		;				189H
JMP$INMODEM	DS	3		;				18CH
JMP$NXTSCRN:	DS	3		;				18FH
JMP$TIMER:	DS	3		;				192H
;
; Clear sequences -- CLREOS is clear to end of screen, CLRSCRN is clear
; entire screen.  Last entry must be 0.  Any other 0's act as NOP's.
;
CLREOS: 	CALL	JMP$ILPRT	;				195H
		DB	ESC,4AH,0,0,0	;				198H
		RET			;				19DH
;
CLRSCRN:	CALL	JMP$ILPRT	;				19EH
		DB	ESC,'T71',0	; For Royal RGB monitor		1A1H
		RET			;				1A6H
;
;
SYSVER: 	CALL	JMP$ILPRT	;				1A7H
		DB	'Version for Royal 8251-A Chip port 40H'	
		DB	CR,LF,0
		RET
;
;
;
;-----------------------------------------------------------------------
;
; NOTE:  You can change the SYSVER message to be longer or shorter.  The
;	 end of your last routine should terminate by 0400H (601 bytes
;	 available after start of SYSVER) if using the Hayes Smartmodem
;	 or by address 0C00H (2659 bytes) otherwise.
;
;-----------------------------------------------------------------------
;
; You can put in a message at this location which can be called up with
; CTL-O if TRANLOGON has been set YES.	You can put in several lines if
; desired.  End with a 0.
;
;
LOGON:	  DB	'This is a Royal Alphatronic computer',CR,LF,0
;
;=======================================================================
;
; This routine allows a 300 ms. break tone to be sent to reset some
; time-share computers.
;
SENDBRK:  MVI	A,1FH
	  JMP	GOODBYE1
;.....
;
;
; This routine sends a 300 ms. break tone and sets DTR low for the same
; length of time to disconnect some modems such as the Bell 212A, etc.
;
GOODBYE:  MVI	A,15H		;SEND BREAK, TURN OFF DTR
;
GOODBYE1: OUT	MODCTL1 	;SEND TO STATUS PORT
	  MVI	B,3		;DELAY ABOUT 300 MS.
	  CALL	JMP$TIMER
	  MVI	A,07H		;NORMAL SEND/RECEIVE WITH DTR
	  OUT	MODCTL1 	;SEND TO STATUS PORT
	  RET
;
;  Royal Alphatronic 8251-A USART initialization sequence Port 41H
;
INITMOD:  MVI	A,0CH
	OUT	MODCTL2
	MVI	A,40H
	OUT	MODCTL2
	MVI	A,4EH
	OUT	MODCTL2
	MVI	A,37H
	OUT	MODCTL2
	RET 
;
;
SETUPR: RET
;
;	       (END OF INITMOD AND SETUP ROUTINES)
;=======================================================================
;
; These routines can be used for your equipment, be sure to end with RET
; If using the Hayes Smartmodem this is unavailable without a special
; change.
;
SPCLMENU: RET
;		
;=======================================================================
;
;
; NOTE:  MUST TERMINATE PRIOR TO 0400H (with Smartmodem)
;				 0BC0H (without Smartmodem)
;
	  END
;
