2 5 1 2 8 A MAXTOR NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 2.5"/SUPERSLIMLINE Cylinders 1092| 1024| 981| Capacity form/unform 128/ MB Heads 4| 14| 10| Seek time / track 15.0/ 3.0 ms Sector/track | 17| 17| Controller IDE / AT Precompensation Cache/Buffer 32 KB ON-BOARD Landing Zone Data transfer rate 1.500 MB/S int Bytes/Sector 512 8.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5 V Temperature *C 5 55 | -40 60 Power: sleep 0.2 W Humidity % 5 90 | 5 90 standby W Altitude km -0.061 3.048| 12.125 idle 1.1 W Shock g 10 | 100 seek W Rotation RPM 3551 read/write 2.2 W Acoustic dBA 34 spin-up W ECC Bit MTBF h 250000 Warranty Month 12 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 25128A/2585A PRODUCT DESCRIPTION +---------------------------------------------------------+ | | | 42XX +5V | |XX | |XX I | |XX N | |XX T | |XX E | +-+J304 20.X R | | |J305 |XX F | | |J306 |XX A | | |J308 |XX C | | |J309 |XX E | +-+J307 |X1 | AxxD Test | | +---------------------------------------------------------+ +----------------------------------------------------------+ | | | +Pin 41 +5V Supply | | +--+-----------------------------------------------+ | | +-+++-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | | | |.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|.|1| |.| A| | | | |.|.|.|.|.|.|.|.|.|.|.| |.|.|.|.|.|.|.|.|.| |.| D| | | +-+++-+-+-+-+-+-+-+-+-+-+++-+-+-+-+-+-+-+-+-+-+-+-++ | +---+ | 20 Key |+---+ Pin 42 Factory Test Point +5V Supply ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 25128A/2585A PRODUCT DESCRIPTION Jumper Setting ============== +----------------------------------+------+------+------+------+ | |J306 |J307 |J308 |J309 | |Master/Slave | | | | | +----------------------------------+------+------+------+------+ |Only drive in single drive system*| | |CLOSED| | +----------------------------------+------+------+------+------+ |Master in dual drive system | | |CLOSED| | +----------------------------------+------+------+------+------+ |Slave in dual drive system | | |OPEN | | +----------------------------------+------+------+------+------+ +----------------------------------+------+------+------+------+ | |J306 |J307 |J308 |J309 | |Reserved for factory | | | | | +----------------------------------+------+------+------+------+ |Normal operation* | |OPEN | |OPEN | +----------------------------------+------+------+------+------+ |Factory operation | |CLOSED| |CLOSED| +----------------------------------+------+------+------+------+ +----------------------------------+------+------+------+------+ | |J306 |J307 |J308 |J309 | |Idle Mode Latch | | | | | +----------------------------------+------+------+------+------+ |Option Disabled* |OPEN | | | | +----------------------------------+------+------+------+------+ |Option Enabled |CLOSED| | | | +----------------------------------+------+------+------+------+ * = Default J304 and J305 reserved for future use. Abnormal operation may occur if reserved jumpers are altered. ********************************************************************** I N S T A L L ********************************************************************** MAXTOR 25128A/2585A PRODUCT DESCRIPTION Sector Address Tranlation ------------------------- 2500 Series drives feature a Universal Translate Mode. In an AT-class system, the drive may be configured to any specified combination of cylinders, heads, and sectors (within the range of the drive's formatted capacity). 2500 Series drives power-up in a Translate Mode: Model Cylinders Heads Sectors 25128A 1024 14 17 2585A 981 10 17 The Maxtor 2500 Series are designed expressly for today's battery- powered notebook and laptop computers. ********************************************************************** G E N E R A L ********************************************************************** MAXTOR IDE INSTALLATION INSTALLATION PROCEDURE FOR AN IDE DRIVE --------------------------------------- 1. Install a 40 pin Data Cable ensuring that pin 1, which can be identified by the striped edge of the cable, is closest to the power connector on the drive. 2. Install a DC power cable to the back of the drive. 3. Verify the jumper configurations for Master/Slave operation (Note: Master will be the bootable drive. The slave will not be bootable.) Also make sure the existing C: drive is jumped to be the Master in a two drive system, not the only drive in the system. 4. Apply power to the computer. 4a. When memory test is complete go into your system's Standard CMOS set-up. (Note: There are various ways to get into CMOS set-up, please refer to system's manual for instructions.) 4b. If your system's BIOS supports a user programmable drive type, program the BIOS with the default parameters of your drive. If your system does not support a user programmable drive type choose parameters that closely match but do not exceed the drives MegaByte capacity. Escape from set-up then choose write to CMOS and exit. 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on it. At the A> prompt type in FDISK. At the menu options select option 1 to create a DOS partition. Another menu will appear and from those options choose 1 to create a Primary DOS partition. Select yes to make 1 large partition and it will automatically become active. Then escape from FDISK. 6. At the A> prompt type in FORMAT C:/S This does a high-level format on the drive and transfers the system files in order for the drive to be bootable. (Note: IDE drives are low-level formatted from the manufacturer and only need a high-level format). To configure the drive as a slave drive repeat steps 1-4 and proceed with steps 5a. and 6a. as follows: 5a. At the C> prompt type in FDISK. When the menu options appear select option 5 to switch to the second drive. Enter fixed disk drive number 2. Then choose option 1 to create a DOS partition, then select option 1 again to create a Primary DOS partition or option 2 to create an Extended DOS partition. (Note: C and D drives will always be the Primary partitions but only the Primary partition on C: will have a status of active). 6a. Proceed with a high-level format on the drive by typing FORMAT D: (Note: Make sure the correct drive letter has been selected for format). 7. The drive is now bootable. As a test remove the DOS diskette from A and press reset to reboot the computer, a C> should be displayed, the drive is now ready for operation.