M K - 1 3 4 F A TOSHIBA NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 733| | | Capacity form/unform 42/ 53 MB Heads 7| | | Seek time / track 25.0/ 7.0 ms Sector/track 32| | | Controller MFM / ST506 Precompensation 512 Cache/Buffer KB Landing Zone Data transfer rate 0.625 MB/S int Bytes/Sector 256 0.625 MB/S ext Recording method MFM operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 40 | -40 70 Power: sleep W Humidity % 8 80 | 5 90 standby W Altitude km -0.300 3.000| -0.400 15.000 idle 10.0 W Shock g 10 | 40 seek W Rotation RPM 3600 read/write W Acoustic dBA 48 spin-up W ECC Bit WITH 11BIT BURST COR MTBF h 30000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** TOSHIBA MK-130FA PRODUCT SPECIFICATIONS 71Y101562, REV. A +---------------------------------------------------------+ | Factory |XX | +---+PJ5 |XX | 1---+ |XX J2 | |XXData | | 1 | |XX | 1-+PJ4 |XX | | | |XX J1 | | | |XXControl | | | |XX | | | |XX | | | |XX | +-+ |XX | |XX ++ | 1 ++LED 1XXXXXX Power +---------------------------------------------------------+ J3 ********************************************************************** J U M P E R S ********************************************************************** TOSHIBA MK130FA PRODUCT SPECIFICATIONS 71Y101562, REV. A Jumper Setting ============== PJ4 --- +-2-----------------------------32+ | o o o o o o o o o o o o o o o o | | o o o o o o o o o o o o o o o o | +-1-----------------------------31+ The 32 pin connector for the selectable functions is provided on the printed circuit board. The specific functions are selected by the jumper plugs to the pins on this connector. Pins Definitions Meanings ------------------------------------------------------------------- 01, 02 WRITE PROTECT Write protected when the jumper plug is connected. 03, 04 RADIAL MODE The drive is always selected when the jumper plug is connected. 05, 06 DRIVE NO. 4 UNIT NO. 4 is assigned when the jumper plug is connected. 07, 08 DRIVE NO. 3 UNIT NO. 3 is assigned when the jumper plug is connected. 09, 10 DRIVE NO. 2 UNIT NO. 2 is assigned when the jumper plug is connected. 11, 12 DRIVE NO. 1 UNIT NO. 1 is assigned when the jumper plug is connected. 13, 14 ---+ 15, 16 | 17, 18 +--- TERMINATOR Should be closed on the last drive on the 19, 20 | daisy-chain. 21, 22 | 23, 24 ---+ 25, 26 ---+--- FOR ADJUSTMENT USE ONLY 27, 28 ---+ 29, 30 ---+--- DRIVE MODEL 31, 32 ---+ Drive ID -------- Five pairs are assigned to set the drive number. By these pairs, it is possible to set any drive ID from 1 to 4 or to set radial connection. Write protect ------------- Write protection is activated by the jumper plug to the pair of pins of the connector. Terminators ----------- Terminator resistors are connected to the interface signals when plugged. Miscellanious ------------- Two pairs of pins for the drive model definition and two pairs for the adjustment are prepaired in the connector. These pairs must not be changed by the customer. Indicator LED ------------- The indicator LED and the connector for additional external indication are prepared at the front on the printed circuit board. The signal for indication becomes "ON" when the both UNIT SELECTED and READY signals are "TRUE". PJ5 FACTORY RESERVED -------------------- 1-3 MUST OPEN, and 4 must CLOSED ********************************************************************** I N S T A L L ********************************************************************** TOSHIBA MK-130FA PRODUCT DESCRIPTIONS 71Y101562, REV. A Notes on installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | x | | | | | | | | x+----------------+x +-+-----------------+-+ | | | | | | ||x x|| +---------------------+ | | | | | | || x x || | | | | | | || x x || x x | | | | | | || x x || +------x------x-------+ | +-----+ +-----+ | || xx || +-+------x--x-------+-+ +--+ +--+ || x x || | xx | || x x || | x x | || x x || +---x--------x----+ |x x| x x x++----------------++x UNACCEPTABLE! UNACCEPTABLE! Never install PC board on the Top! Mounting Instructions --------------------- When mounting the drive, the cabinet frame should keep apart 0.1 inch (2.5 mm) or more distance from the outer surface of the HDA and PCB for vibrating space. Use 4 tap holes located on both sides or bottom side of the drive frame for fixing the drive. Screws should not be penetrated more than 2.5mm from the outer surface of drive frame to keep clearance between screw tips and PCB. The drive frame is isolated from the HDA (signal ground). Mounting screws M3X0.5, four in bottom, two in each side. Cooling ------- Cabinet packaging designs must provide ample air circulation around the drive to ensure environmental limits are not exceeded. J1 Control Signal Connector --------------------------- Drive side connector: Card edge (gilded) No. of poles and pitch: 34 poles, 0.1-inch pitch (17-pole double side, even numbered on the component side) Porality key slot: Between pin No. 4 and 6 Cable-side applicable connector: AMP ribbon connector P/N 88373-3 or Molex P/N 15-35-1341 Flat cable or twisted pair 6m max. J2 Data Signal Connector ------------------------ Drive side connector: Card edge (gilded) No. of poles and pitch: 20 poles, 0.1-inch pitch (10-pole double side, even numbered on the component side) Porality key slot: Between pin No. 4 and Cable-side applicable connector: AMP ribbon connector P/N 88373-6 or Molex P/N 15-35-1201 Flat Cable or twisted pair 6m max. J3 Power Input Connector ------------------------ Drive side connector: AMP P/N 350211-1 or equivalent No. of poles: 4 poles Porality: Poralized by the form of the connector housing Cable-side applicable: AMP P/N 1-480424-0 and pin P/N 350078-4 (chain type) or 61173-4 (loose type) Power cable: Must meet the maximum current consumption of the drive an dthe voltage at the connector end. J4 Frame Ground Connector ------------------------- The HDA module (head/disk assembly container) and DC ground (signal 0V) are short-circuited at the time of factory shipment. However, the frame (the part where the mounting tap holes are provided) is isolated from DC ground. DC ground connector Drive side : Faston terminal AMP P/N 61761-2 Mating connector : Faston terminal AMP P/N 62187-1 DC Power and pin connector assignments -------------------------------------- pin 1 +12 VDC pin 2 +12 Volts Return pin 3 + 5 Volts Return pin 4 + 5 VDC Cable Interconnection - 4 Drive System -------------------------------------- HOST +-----------+ +-----------------+ | +---o---Control------------------+J1 Drive 1 | | | | +-------Data------------+J2 | | | | | +-Power---+J3 GROUND TAB |+-+ | | | | | +-----+-----------+ | | | | | | +-Frame----+ | | | | | | | +-----------------+ | |Controller | o----+-------------+----+----+J1 Drive 2 | | | | | | +-----------+----+----+J2 | | | | | | | o----+----+J3 GROUND TAB |+-+ | | | | | | | +----+------------+ | | | | | | | o---------+ | | | | | | | | +-----------------+ | +-----------+ o----+-+-----------+----+----+J1 Drive 3 | | | | | | | +---------+----+----+J2 | | | +---+----+ | | o----+----+J3 GROUND TAB |+-+ | +---+------+ | | | +-----+-----------+ | | | | | | o----------+ | |Data +---+--------+ | | +-----------------+ | |Separator | +------------------+----+----+J1 Drive 4 | | | +----------------------+----+----+J2 | | | | o----+----+J3 GROUND TAB |+-+ +-----------+ | | +-----+-----------+ | DC voltages ---+ o----------+ | | | Signal Ground ------+ | | Frame Ground ---------------------------------+ NOTE It is necessary to set ON the terminator by the jumper plug at the last drive in connection. Terminator resistance networks for the other drives must be set to OFF. The total length of control signal cables for four drives must not exceed 6 meters. The maximum cable length of a data signal cable is 6 meters. ********************************************************************** F E A T U R E S ********************************************************************** TOSHIBA MK-130FA PRODUCT SPECIFICATIONS 71Y101562, REV. A General Description ------------------- The MK130FA magnetic disk drive is a fixed magnetic disk drive with standard 3.5-inch magnetic disks as recording media. The size and mounting details are identical to the industry standard mini floppy disk drives. The MK130FA is a high-performance magnetic disk drive featuring high-speed access, a recording capacity of 23 to 54 Megabytes and high reliability employing the Winchester technologies and closed loop servo control. The disks are driven directly by a DC spindle motor. Air filtration is provided by means of a high performance air circulation filter system using breather and circulation filters. The drive provides an automatic carriage lock mechanism to prevent the damage during non- operating and transportation. The printed circuit board contains all the electronic circuitry necessary to drive the equipment. The circuit board is provided outside outside the HDA and has power input and interface signal connectors. The circuit board contains an interface circuit read/write circuit, spindle motor control circuit, access (seek) and head positioning servo control circuit and abnormal condition detecting circuit. Options ------- 1. Control signal cable 2. Data transmission signal cable 3. Front panel Write Precompensation --------------------- Cylinders to be compensated: Cyl. 512 to cyl. 732 Compensation time: 12ns Media Defect ------------ A media defect is a physical defect on media (disk). Such a defect causes read errors repeatedly even if this drive is properly adjusted and operated in a normal environmental condition. Valid data must not be written deallocation or skip displacement techniques must be utilized. 1. Number of defects +-----------------+---------+---------+---------+ |Model | MK132FA | MK133FA | MK134FA | +-----------------+---------+---------+---------+ |Max. per drive | 30 | 40 | 50 | |Max. per surface | 15 | 15 | 15 | +-----------------+---------+---------+---------+ 2. Defect-free tracks Head 0 and head 1 of cylinder 000 have no defect for all models at the time of factory shipment. 3. At the time of factory shipment, there does not exist any defect that causes an error of 11 and more consecutive bits. Therefore, almost all defects may be corrected if ECC (Error Correction Code) that can correct a 11-bit error is used. Defective Sector Flag --------------------- At the time of factory shipment, a data sheet is attached to the drive, indicating the positions of defective sectors or sectors with poor recording quality. The defective positions are indicated by the head numbers and the byte address from the INDEX.