OLICOM, INC.

OC-3230 TR/MODEM 144

Card Type

Modem(asynchronous), Fax, NIC

Chip Set

Texas Instruments TMS 380C25

Maximum Onboard Memory

32KB, 128KB for LAN buffers

Network Rate

4/16Mbps

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA Type II

Fax Class

Class I & II

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation Protocol

Unidentified

Error Correction/Compression

MNP10, V.42bis

Topology

Token Ring

Wiring Type

Shielded/Unshielded twisted pair

Boot ROM

128KB PROM

V1802/N1433

Proprietary AT Command Set

AUTO-RETRAIN - FALLBACK/FALLFORWARD

Type:

Configuration

Format:

AT [cmds] %E n [cmds]

Description:

Controls auto-retrain mode and fallback/fall forward.

Command

Function

%E0

Auto-retrain disabled

%E1

Auto-retrain enabled

%E2

Auto-retrain and Fallback/fall forward enabled

%E3

Auto-retrain and Fallback/fall forward with fast hang up enabled

BREAK SEND

Type:

Configuration

Format:

AT [cmds] \B n [cmds]

Range:

1-9

Unit:

.1 second

Description:

Sends break of n to modem

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \K n [cmds]

Description:

Configures action of break signal

Command

Break from DTE

Reliable/Normal mode

Modem receives \B

Break from remote modem

\K0

Enter command mode, do not send break to remote modem.

Buffers cleared and break sent to remote modem.

Buffers cleared and break sent to DTE.

\K1

Buffers cleared and break sent to remote modem.

Buffers cleared and break sent to remote modem.

Buffers cleared and break sent to DTE.

\K2

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately.

Send break to DTE immediately.

\K3

Send break to remote modem immediately.

Send break to remote modem immediately.

Send break to DTE immediately.

\K4

Enter command mode, do not send break to remote modem.

Send break to remote modem with transmitted data.

Break sent with received data to the DTE.

\K5

Send break with transmitted data.

Send break to remote modem with transmitted data.

Break sent with received data to the DTE.

CELLULAR TRANSMISSION LEVEL

Type:

Configuration

Format:

AT [cmds] @M n [cmds]

Default:

Unidentified

Range:

0 - 31

Unit:

-1 dBm

Description:

Sets the signal level for transmission when in leased line mode

CHANGE COUNTRY CODE

Type:

Configuration

Format:

AT [cmds] *NC nn [cmds]

Description:

Changes country code to one of 8 stored in NVRAM

COMPRESSION

Type:

Configuration

Format:

AT %C n

Description:

Selects data compression.

Command

Function

%C0

Data compression disabled

%C1

MNP5 enabled

%C2

V.42bis enabled

%C3

MNP5 and V.42bis enabled

COMPROMISE EQUALIZER

Type:

Configuration

Format:

AT [cmds] :E n [cmds]

Description:

Controls compromise equalizer

Command

Function

:E0

Equalizer disabled

:E1

Equalizer enabled

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \N n [cmds]

Description:

Sets connect mode

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

\N3

Auto-reliable mode enabled

\N4

LAPM mode only enabled

\N5

MNP mode only enabled

DISPLAY CURRENT CONFIGURATION

Type:

Immediate

Format:

AT [cmds] \S [cmds]

Description:

Displays current command profile

DISPLAY DELAYED NUMBERS

Type:

Immediate

Format:

AT [cmds] *B [cmds]

Description:

Displays list of delayed numbers

DISPLAY DELAYED NUMBERS

Type:

Immediate

Format:

AT [cmds *D [cmds]

Description:

Displays list of of delayed numbers

DISPLAY LINE SIGNAL LEVEL

Type:

Immediate

Format:

AT [cmds] %L [cmds]

Description:

Displays received line signal level in dBm

DISPLAY LINE SIGNAL QUALITY

Type:

Immediate

Format:

AT [cmds] %Q [cmds]

Description:

Displays line signal quality

DISPLAY STORED NUMBERS

Type:

Immediate

Format:

AT [cmds] \F [cmds]

Description:

Displays all stored phone numbers

FALL-BACK

Type:

Configuration

Format:

AT [cmds] -Q n [cmds]

Description:

Enables fall back to V.22/V.22bis

Command

Function

-Q0

V.22/V.22bis fall back enabled

-Q1

V.22/V.22bis fall back disabled

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] \G n [cmds]

Description:

Enables modem port flow control

Command

Function

\G0

Flow control disabled

\G1

Flow control enabled

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] \J n [cmds]

Description:

Sets operation of serial port speed

Command

Function

\J0

Serial speed locked

\J1

Serial speed follows connect speed

MAXIMUM MNP BLOCK

Type:

Configuration

Format:

AT [cmds] \A n [cmds]

Description:

Sets the maximum transmission block size

Command

Function

\A0

MNP block size is 64 characters

\A1

MNP block size is 128 characters

\A2

MNP block size is 192 characters

\A3

MNP block size is 256 characters

MNP10 COMPRESSION

Type:

Configuration

Format:

AT [cmds] -K n [cmds]

Description:

Selects MNP10 data compression

Command

Function

-K0

MNP10 disabled

-K1

MNP10 enabled

MNP 10 HANDSHAKE

Type:

Configuration

Format:

AT [cmds] *H n [cmds]

Description:

Selects MNP 10 link negotiation speed

Command

Function

*H0

MNP 10 handshake at highest common speed

*H1

MNP 10 handshake at 1200bps

*H2

MNP 10 handshake at 4800bps

MNP10 POWER LEVEL ADJUST

Type:

Configuration

Format:

AT [cmds] )M n [cmds]

Description:

Controls automatic transmit power level adjustment during MNP 10 link negotiation

Command

Function

)M0

Power level adjustment disabled

)M1

Power level adjustment enabled

MNP STREAM/BLOCK MODE

Type:

Configuration

Format:

AT [cmds] \L n [cmds]

Description:

Selects the transfer mode for MNP

Command

Function

\L0

Stream mode for MNP enabled

\L1

Block mode for MNP enabled

PROTOCOL/SPEED

Type:

Configuration

Format:

AT [cmds] F n [cmds]

Description:

Selects protocol and line speed used

Command

Function

F0

Select fastest common protocol

F1

V.21/Bell 103A

F3

Not used

F3

V.23

F4

V.22/Bell 212A 1200bps

F5

V.22bis 2400bps

F6

V.32bis/V.32 4800bps

F7

V.32bis 7200bps

F8

V.32bis/V.32 9600bps

F9

V.32bis 12.0Kbps

F10

V.32bis 14.4Kbps

PULSE DIAL CODE

Type:

Configuration

Format:

AT [cmds] *Z n [cmds]

Description:

Selects digit used for pulse dial code

Command

Function

*Z0

Use dial code 0

*Z1

Use dial code 1

REMOTE CONFIGURATION PASSWORD

Type:

Configuration

Format:

AT [cmds] *C n [cmds]

Description:

Store remote configuration password

REMOTE MNP

Type:

Configuration

Format:

AT [cmds] *R [cmds]

Description:

Requests remote modem’s MNP configuration

SETUP PASSWORD

Type:

Configuration

Format:

AT [cmds] *P xxxx / yyyy [cmds]

Description:

Changes the modem’s password and callback number. xxxx represents the password, and yyyy represents the callback number.

V.23 SPLIT BAUD MODE

Type:

Configuration

Format:

AT [cmds] \W n [cmds]

Description:

Controls V.23 split baud mode

Command

Function

\W0

V.23 split baud mode disabled

\W1

V.23 split baud mode enabled

VIEW DATA

Type:

Configuration

Format:

AT [cmds] %F n [cmds]

Description:

Selects split transmit and receive line speeds during viewdata operation

Command

Function

%F1

75bps transmit/1200bps receive when viewdata selected

%F2

1200bps transmit/75bps receive when viewdata selected

S REGISTERS

Register

Function

Default

S14

Bit mapped

Unidentified

S16

Bit mapped test options

Unidentified

S20

Bit mapped

Unidentified

S21

Bit mapped

Unidentified

S22

Bit mapped speaker options

Unidentified

S23

Bit mapped

Unidentified

S24

Sleep inactivity timer

0

S27

Bit mapped

Unidentified

S28

Bit mapped

Unidentified

S29

Flash modifier timer

0

S31

Bit mapped

Unidentified

S33

XOFF character

19

S40

Bit mapped

Unidentified

S41

Bit mapped

Unidentified

S80

Soft switch

Unidentified

S99

Leased line transmit level

Unidentified

S201

Cellular transmit level

Unidentified

S202

Remote escape character

Unidentified